Atlas
Barbell Glute Bridge: starting position Barbell Glute Bridge: end position

Hip Extension · Glutes

Barbell Glute Bridge

A hip extension exercise that works the glutes. Intermediate level, using barbell & rack.

The barbell glute bridge is a hip extension exercise where you lie on the floor and drive your hips up with a loaded barbell across your pelvis. It lets you move heavy weight with little stress on your spine. It is ideal for intermediate lifters chasing glute strength and size, and it is simpler to set up than the hip thrust.

IntermediateBarbell & rackGym

Muscles worked

PrimaryGlutes
SecondaryCalves (gastrocnemius & soleus), Hamstrings

Your glutes do most of the work because the load peaks at full hip extension. Your hamstrings help extend the hip, while your calves and core stabilize your feet and torso.

Setup and loading

Use a padded bar or folded mat across your hips, and large plates so you can roll the bar over your pelvis. Choose a weight that allows 8 to 12 reps with a pause at the top and no lower back arch.

How to do the barbell glute bridge step by step

  1. Sit on the floor with legs straight and roll the padded barbell up until it rests in the crease of your hips.
  2. Lie back, bend your knees, and plant your feet flat at hip width, about a hand's length from your glutes.
  3. Hold the bar with both hands, tuck your chin, and tilt your pelvis slightly under with your abs braced.
  4. Exhale and drive through your heels to lift your hips until your shoulders, hips, and knees form a line.
  5. Squeeze your glutes for one or two seconds at the top without arching your lower back or flaring your ribs.
  6. Inhale and lower your hips under control until they lightly touch the floor, then repeat without losing tension.

Form cues

  • Tuck your chin and look toward your knees
  • Tilt your pelvis under at the top
  • Push through your heels, not your toes
  • Pause at the top and squeeze hard

Common mistakes

  • Arching your lower back at the top: your back takes over; pull ribs down and tuck your pelvis.
  • Feet too far away: your hamstrings take over and may cramp; bring feet in until shins are vertical.
  • Using a bare bar: it hurts and limits load; use a thick pad or a folded mat.
  • Bouncing off the floor: you lose glute tension; lower under control and lift without momentum.

How to make it easier or harder

To regress, do bodyweight glute bridges or hold a dumbbell across your hips. To progress, add load, wrap a band around your knees, or move to the hip thrust with your back on a bench.

Advertisement

Sets and reps for your goal

Max Strength

4-5 x 3-6 · rest 2-3 min

3-6 sets of 1-6 reps at 80-90% of your max (1RM). Rest 2 to 5 minutes.

Leave 1-3 reps in reserve. If your technique breaks down, lower the weight: strength is built with good reps.

A guide for healthy adults. Adjust the load to your level and see a professional if you have an injury.

Check your form

Film yourself from the side or ask someone to watch, then tick what you get right.

0 of 4

Frequently asked questions

What is the difference between a glute bridge and a hip thrust?

In a glute bridge your back is on the floor, so the range is shorter. In a hip thrust your back rests on a bench, the range is longer, and you can often load more. Both train the glutes very well.

Why do I feel glute bridges in my hamstrings?

This usually happens when your feet are too far out or you push through your toes. Bring your feet closer, drive through your heels, and tuck your pelvis at the top so your glutes do most of the work.

Sports it suits

Gear for this exercise

  • Olympic barbell and platesTo keep progressing on the big lifts with heavy loads.

As an Amazon Associate, Muscle Atlas earns from qualifying purchases.

Variations and similar exercises

Advertisement