Atlas
Jerk Dip Squat: starting position Jerk Dip Squat: end position

Olympic Lifts · Quads

Jerk Dip Squat

A olympic lifts exercise that works the quads. Intermediate level, using barbell & rack.

The jerk dip squat is a strength drill where, with the bar in the front rack, you perform only the short dip and drive of the jerk without launching the bar. It trains torso position and leg drive in the dip using loads heavier than your jerk. It is an accessory for intermediate weightlifters.

IntermediateBarbell & rackGym

Muscles worked

PrimaryQuads
SecondaryAbs, Calves (gastrocnemius & soleus)

Your quads do most of the work in the partial dip and drive, with calves active at the finish. Your abs take a heavy load to keep the torso from tipping forward or collapsing.

Technical lift: the photos show the start and end positions. Learn the full bar path with a coach.

Setup and loading

Unrack the bar into the front rack from hooks at shoulder height, with safeties set slightly lower. Most lifters work at 100 to 130 percent of their jerk, as long as the dip stays vertical and controlled.

How to do the jerk dip squat step by step

  1. Unrack the bar into the front rack with elbows slightly forward and feet hip width apart.
  2. Take a deep breath and brace hard, with weight spread across your whole foot.
  3. Dip your knees a few inches straight down, pushing them slightly out while keeping your torso fully upright.
  4. Stop briefly and under control at the bottom, without letting the bar push your torso forward.
  5. Drive up through your legs onto or nearly onto your toes, without pressing with your arms.
  6. Exhale at the top, reset your position, and repeat or return the bar to the rack.

Form cues

  • Keep your torso vertical, like dipping through a tube
  • Weight across the whole foot, not the toes
  • Short dip, never a half squat
  • Drive hard without using your arms

Common mistakes

  • Tipping forward in the dip: the bar moves out front; keep your chest up and vertical.
  • Dipping too deep: it turns into a squat; limit it to a few inches.
  • Weight on the toes: you lose stability; keep it balanced or slightly toward the heels.
  • Dropping elbows: the bar rolls forward; keep them high and in front.

How to make it easier or harder

To make it easier, practice with light loads or paused dips without the drive. To progress, add weight, include a two second pause before driving, or pair it with push presses and jerks.

Advertisement

Sets and reps for your goal

Power

4-6 x 2-5 · full rest

3-6 sets of 1-5 reps with light or moderate loads (30-60% of your max on the main lifts), or with a ball or your bodyweight. Rest 2 to 3 minutes.

Every rep at the highest possible speed. As soon as you notice it moving slower (a 10-20% velocity loss), end the set. Train power fresh, never fatigued.

Max Strength

4-5 x 3-6 · rest 2-3 min

3-6 sets of 1-6 reps at 80-90% of your max (1RM). Rest 2 to 5 minutes.

Leave 1-3 reps in reserve. If your technique breaks down, lower the weight: strength is built with good reps.

A guide for healthy adults. Adjust the load to your level and see a professional if you have an injury.

Check your form

Film yourself from the side or ask someone to watch, then tick what you get right.

0 of 4

Frequently asked questions

What are jerk dip squats for?

They strengthen the dip and drive of the jerk and teach you to keep a vertical torso under heavy loads. Many missed jerks come from a forward leaning dip, and this drill fixes that position.

How heavy should jerk dips be?

Typically 100 to 130 percent of your best jerk, since you only do the drive portion. Always use rack safeties and lower the weight if your dip starts tipping forward.

Sports it suits

Gear for this exercise

  • Olympic barbell and platesTo keep progressing on the big lifts with heavy loads.

As an Amazon Associate, Muscle Atlas earns from qualifying purchases.

Variations and similar exercises

Advertisement